FF-10 (T10C) R6014FS 2,4 GHz Futaba Robbe F7032 1-F7032
Fully expanded ten-channel computer system of superior quality, with 2.4 GHz FASST technology. The FASST system is a Spread Spectrum system with frequency hopping (FHSS), and is therefore permitted to transmit a maximum power of 100 mW EIRP. This gives it adequate reserves even for large-scale model aircraft and jets.
No crystals, no spot frequency selection, maximum security from same-channel interference.
Virtually interference-free due to Spread Spectrum modulation, frequency hopping and encoding from transmitter to receiver using more than 130 million codes.
Please see the FASST introduction page for a detailed description of the advantages of 2.4 GHz FASST technology.
Focal point of the transmitter is the large, high-resolution 160 x 72 dot graphic screen with extra-large dots for good legibility. All settings are entered and displayed using the screen itself. The system is very simple to program using the four control buttons, the 3-D hotkey and the graphical user interface.
New precision dual-axis stick units with digital trims and variable trim increments eliminate the need to make trim adjustments or store trim values when you switch model memories. The trim values are displayed on the LCD screen in bar graph form.
The side-mounted rotary controls provide a practical means of operating supplementary functions without letting go of the primary sticks.
The transmitter is fully expanded as standard, with five analogue rotary controls and eight switches; no additional accessories are required. The switches and other transmitter controls can be assigned to virtually any function.
New feature: logical switch function for switches and sticks.
Comprehensive software provides all the essential facilities even for power models, gliders and helicopters with extensive functions.
Plenty of freely programmable mixers are available with up to 5-point curves for setting up very complex mixer functions.
The transmitter can also operate in FM or PCM transmission mode; the FM-TW 10 RF module is required for this. It is then compatible with all current FM and PCM-1024 receivers in the robbe/Futaba range.
In FASST 2.4 GHz mode the system offers a total of ten channels (eight proportional, two switched channels).
The software is available in six languages: German, English, French, Italian, Spanish and Dutch.
Integral H3 (1:1:1) swashplate mixer for CCPM rotor head control (140°), plus H4X for 45° swashplate rotation.
Integral Trainer system with individual function transfer.
With charge socket, i.e. prepared for use with rechargeable batteries.
The stick units are designed for Universal mode, and can be converted by the user from "throttle right" to "throttle left".
Fifteen internal model memories, with infinite expansion using CAMPac modules:
4k CAMPac module = 1 model
16k CAMPac module = 4 models
64k CAMPac module = 16 models
16 x 64k CAMPac module = 256 models
|
| Optional |
Functions
Model select, fifteen internal model memories, can be expanded by up to sixteen models per 64k CAMPac module
Operating hours counter: 0 ... 99h:59mDigital operating voltage display
Stick modes 1 ... 4
Throttle reverse function
Model copy
Trainer mode with individual function transfer and mix mode operation.
LCD contrast adjustment
Graphical servo travel display with servo test
User´s name (ten characters)
Digital stick trims
Model functions
Model name (ten characters)
Three separate stopwatches (one model memory-specific)
Servo reverse, channels 1 - 8
Fail-safe (channels 1 - 8), PCM and FASST only
Mixer select menus for power, glider and helicopter
Servo travel adjustment, channels 1 - 8 (ATV / EPA)
Reset
Trim travel adjustment and trim memory
Idle trim with reverse (ATL)
Free assignment of transmitter controls for channels 5 ... 10
Switchable modulation, FM / PCM1024
Servo centre adjustment (channels 1 - 8)
Three logical switches (switch and / or stick)
Basic functions
4 x Three-point programmable mixers, with / without trim and offset mixing
4 x Five-point programmable mixers, with / without trim and offset mixing (helicopter: only 2 x)
3 x Switchable control travel (D/R)
3 x Exponential function, EXP (acro: 4 x)
Power models (Acro)Flaperon mixer with differential and separate end-point adjustment
Flaperon trim (flaperon mixer value)
Second aileron mixer with differential, output to channel 5 or 6
Airbrake (ailerons as camber-changing / landing flaps)
Elevator -> flaperon mixer
V-tail mixer (V-tail)Delta mixer (elevons)
Separate elevators as ailerons (ailvators)
4 x snap-roll (aileron / rudder / elevator)
Idle-up (increased idle)
Speed adjustment for throttle servo
Mixer adjustment with five-point curve and speed adjustment
Throttle cut
Idle 2 adjustment
Gyro gain adjustment menu
Gliders (two servos)
Flaperon mixer with differential and separate end-point adjustment
Flaperon trim (flaperon mixer value)
Second aileron mixer with differential, output to channel 5 or 7
Butterfly (Crow) for ailerons and camber-changing / landing flaps, with offset and delay for elevator function.
Butterfly - spoiler mixer with offset
Camber-changing flap mixer (aileron, flap, elevator, with delay)
Aileron -> flap mixer
Aileron -> rudder mixer
Elevator -> flaperon mixer
V-tail mixer (V-tail)
Delta mixer (elevon)
Launch and Speed trim menu for ailerons, flaps and elevator, with trim function
Motor cut
Gliders (four servos)
Flap trim (camber-changing / landing flap mixer value)
Flaperon trim (flaperon mixer value)
Second aileron mixer with differential, output to channel 5 or 7
Butterfly (Crow) for ailerons and camber-changing / landing flaps, with offset and delay for elevator function.
Butterfly - spoiler mixer with offset
Camber-changing flap mixer (aileron, flap, elevator, with delay)
Aileron -> flap mixer
Aileron -> rudder mixer
Elevator -> camber-changing / landing flap mixer
V-tail mixer (V-tail)
Camber-changing / landing flap -> aileron mixer
Aileron -> camber-changing / landing flap mixer
Launch and Speed trim menu for ailerons, flaps and elevator, with trim function
Motor cut
Helicopters
Swashplate mixers: H1, H3, HR3, HN3, HE3, H4, H4X (45°)
Swashplate adjustment (AFR - roll, pitch-axis, collective pitch)
Seven-point throttle curve, normal, idle-up 1, 2 and 3, with delay
Seven-point collective pitch curve, normal, idle-up 1, 2 and 3 and auto-rotation
Revo-mixer with five-point curve, normal, idle-up 1, 2 and 3
Swashplate - throttle mixer
Tail rotor - throttle mixer
Gyro gain adjustment menu:
- Standard with three rates, 0 ... 100 %
- GY with three rates, 0 ... +/- 100 % (normal / AVCS), flight mode-dependent
Governor set-up menu (speed regulator), flight mode-dependent
Throttle trim, hover
Collective pitch trim, hover
Auto-rotation with tail rotor offset
Dual offset mixer for roll, pitch-axis and tail rotor functions
Variable delay for the tail rotor function; H1: also for roll and pitch-axis functions
Mixer adjustment with five-point curve for three flight modes
Motor cut
| Specification: |
| Weight: 990 g |
| Channel spacing: 2048 kHz |
| Spotfrequencies: 36.00 |
| Current drain: 230 |
| Power Supply: 9,6 Volt NiMH-Akku |
| Transmission system: FSK |
| Functions: 20/10 Servos |
|
|
| Kit contents: |
1 T10C FASST transmitter, 2.4 GHz
1 Transmitter battery, 9.6 Volt / 2000 mAh
1 TM10 FASST RF module
1 R 6014FS FASST receiver
1 Switch harness with charge socket
|
|
|
| Accessories: |
| Trainer cable FF-9 - FX 2.5mm (1) 1-8236 | |  |
| Trainer cord FF-9 - F 3.5 (1) 1-8238 | | |
| Adapter cable flight simulator FF- (1) 1-8239 | | |
| Campac-modul 16X64K (1) 1-8321 | | |
| Transmitter charge lead (1) 1-F1415 | | |
| Receiver battery charge lead (1) 1-F1416 | | |
| Neckstrap 1 point (1) 1-F1550 | | |
| Alu transmitter case Aero Team (1) 1-F1556 | | |
| Trainer cord FF-9/T14/T12/FX40/30 (1) 1-F1591 | | |
|
|
| Receiver included: |
|
|
|
|
|
This Product was added to our catalogue on Saturday, 02. February 2008.
|
| We recommend following products: |
|
|
|
| This product is compatible too (for example): |
|
|
|
| Customers who bought this product bought also the following products: |
 |
RF-MODUL FP-TW-35 MHZ (FF-9) Robbe 1-F1931 F1931 |
MSRP* 96,40 EUR
your price 86,76 EUR
incl. 19 % Tax
excl.
|
 |
Antriebssatz "Xeno TUNING" Multiplex 332655 |
MSRP* 149,90 EUR
your price 129,90 EUR
incl. 19 % Tax
excl.
|
 |
BK Xeno Multiplex 214239 |
MSRP* 64,90 EUR
your price 39,95 EUR
incl. 19 % Tax
excl.
|
 |
Tiny-MG Multiplex 65122 |
MSRP* 26,90 EUR
your price 21,90 EUR
incl. 19 % Tax
excl.
|
 |
SERVO S 3107 NANO Robbe 1-F1291 F1291 |
MSRP* 20,50 EUR
your price 18,45 EUR
incl. 19 % Tax
excl.
|
 |
Sport Wing weiss + BL-Antrieb Robbe 3282 1-3282 |
MSRP* 191,00 EUR
your price 171,90 EUR
incl. 19 % Tax
excl.
|
|
|
|
| Shopping Cart |
 |
|
| You do not have any products in your shopping cart yet. |
|
| New Products |
|
|
|
|
Customer group:Gast
|
|
| Reviews |
|
|
|
|
|
|
|
Currently 106 Customers are online.
Letztes Update:
09.02.2012 09:25
|
|
Besucher seit Februar 2005
|
|
